Gisco Premium EDM Wires
| Gisco Cobra Cut
| Gisco Topas |
Gisco Bronco Cut |
Gisco MegaCut Gisco Somsal | Gisco Berco Cut | Gisco Micro Cut | Gisco Macro Cut |
| GISCO COBRA CUT FAMILY The coated wire electrode series COBRA CUT® was developed with AGIE for EDM machines. They are suitable for a number of different machine models and for practical applications. |
| Gisco Cobra Cut Soft Brass Core/Tensile Strength 70,000 psi These zinc-coated wire electrodes were initially produced for AGIE for their first AC machines. Due to its elongation, it is particularly suitable for high tapering. It has a limited suitability for machine models with automatic water-jet threading. |
| Gisco Cobra Cut A Hard Brass Core/Tensile Strength 130,000 psi This hard, zinc-coated wire electrode is especially suitable for machines with automatic threaders. Due to its excellent straightness and precision, it guarantees very good surface qualities and allows precision cuts and fine detail with the highest reliability in automatic operations (particularly with .003", .004" and .006" diameter wires). With this wire, steep taper cuts are possible only to a limited extent, except on the following AGIE machine models for which it is specified: AC 100, 200, 300, 100D, 200D and 300D. |
| Gisco Cobra Cut B Soft/Tensile Strength 65,000 psi The special CuMg core of this electrode provides high electrical conductivity. Its rougher, oxidized surface benefits flushing conditions and is advantageous for the cutting of tall work pieces (>4"). Recommended for fast cutting of graphite and aluminum alloys. This wire is suitable for tapering to 20o, but has limited capability for skim cutting and automatic wire threading. It is specified for the following AGIE models: AC 100, 200, 300, 100D, 200D and 300D. |
| Gisco Cobra Cut D ˝ Hard/Tensile Strength 115,000 psi This wire electrode has been developed for EDM machines with high-power generators. It has a high thermal and electrical conductivity due to its special coating. It consists of two CuZn alloys (brass-on-brass), and is therefore suitable for speed cutting as well as for precision contour cutting. It can be used on machines with automatic threading. Tapered cuts (>7°) are possible only to a limited extent, except on the following AGIE machine models for which this wire is specified: AC 100D, 200D, and 300D. |
| Gisco Cobra Cut S ˝ Hard/Hard Brass Core/Tensile Strength 115,000 psi This wire electrode guarantees highest cutting rates on the latest high-power EDM machines. As an improvement of the COBRA CUT® Type D, the thicker diffusion coat provides better cutting performance. It is most suitable for use in high-volume production EDM, tool and die making, and for thick workpieces. It is suitable for automatic threading and is specified for AGIE AC Sprint machines. |
| Gisco Cobra Cut W Soft/Tensile Strength 62,700 psi This diffusion-annealed wire is designed to deliver the high productivity of Cobra® Cut D with the high elongation of BercoCut 390 wire. Suitable to taper cuts up to 45°. |
| GISCO TOPAS FAMILY TOPAS® is the first gamma phase wire from Berkenhoff which can be universally used on all standard EDM machines and achieves excellent cutting rates with high precision and surface quality. Economical production processes demand ever increasing removal rates. Our new TOPAS® electrodes meet these most exacting requirements thanks to their special coating. They cut up to 50% faster than plain wires. In comparison with "hot-dipped" wires, the TOPAS® EDM wires achieve a significantly higher cutting rate. They also offer better fine finishing characteristics compared to diffusion annealed wires. And so the major performance criteria are met without compromise: high precision at fast cutting rates with high surface quality at the workpiece. |
| Gisco Topas S Soft/Tensile strength 70,000 psi TOPAS® S is especially suited for taper cutting with reliable edge-finding. |
| Gisco Topas H Hard/Tensile strength 115,000 psi With its high tensile strength, type H is particularly suited for machines which require straightened wires for threading. A crucial advantage is the universal usability of the TOPAS® EDM wires on all conventional EDM machines with existing standard technologies. This allows considerable performance advantages without involving extra time and costs for reprogramming. |
| GISCO BRONCO CUT FAMILY This coated EDM wire series BRONCO CUT® was initially developed for the special application on Charmilles Technologies EDM machines, it also meets the particular threading requirements of this manufacturer. The manufacturer of Charmilles is introducing this type series on the market with the identification "SW-....". |
| Gisco Bronco Cut Soft/Tensile strength 65,000 psi This zinc-coated copper EDM wire is designed for compatibility with the annealing and calibration devices of earlier Charmilles machines. These are Charmilles F series machines (420, 430, 431 and 453) Charmilles CH series machines (452, 552) and Andrew machines. This wire can be used on these machines for various applications; however, they are suitable for precision cutting only to a limited extent. |
| Gisco Bronco Cut X Soft/Tensile 72,000 psi This high-performance, multipurpose EDM wire with a special zinc-rich coating is suitable for precision cutting as well as high-speed cutting. Excellent automatic threading reliability except for the following Charmilles machines Robofil 100 and 1000 series. Taper cutting (>7°) only to a limited degree. |
| GISCO MEGACUT FAMILY This electrode type MEGACUT® was especially developed for Japanese EDM machines. |
| Gisco MegaCut A Hard/Tensile strength 130,000 psi In small diameters (.003" - .008"), this zinc-coated precision wire is suitable for cuts with tight corner radii. It offers high cutting rates and performs well in critical applications (for example, in tungsten carbide alloys). The wire has excellent manual and automatic threading capabilities. Taper cutting (>7°) is only possible to a limited degree. This wire is in compliance with Mitsubishi EDMs. This wire is used when fine surfaces are required, it is also recommended when cutting carbides and poly-crystalline diamond. |
| Gisco MegaCut HS ˝ Hard/Tensile strength 115,000 psi This electrode is suited for the high-power generators of the latest machines and offers maximum cutting rates, making it ideal for high-speed productions. Type HS has a thicker coating than Type D in order to compensate for the increased consumption of the electrode during high speed cutting. Due to its straightness, the wire is especially suited for machines with automatic threading and was specifically designed for the Mitsubishi HA and U series Wire EDMs. |
| Gisco MegaCut W Soft/Tensile strength 62,700 psi This type has the highest elongation of the MEGACUT® series. The "soft" electrode allows steep tapering. The special coating can resist thermal loads arising from poor flushing conditions. Suitable for taper cuts up to 45°. |
| Gisco MegaCut D ˝ Hard/Tensile strength 115,00 psi Due to its special coating, this electrode is ideal for speed cutting, providing the highest performance. This wire is also recommended for tall workpieces, interrupted cuts and poor flushing conditions. For taper cutting (>7°), this wire is suitable only to a limited extent. Type D wire complies with Mitsubishi EDMs. |
| Gisco MegaCut T Soft/Tensile strength 70,000 psi This wire electrode is similar to MEGACUT® Type A but has reduced hardness, making it perfectly suitable for high tapering requirements. Because of this increased tapering capability, this wire will have limited automatic threading capability. It is a soft zinc coated brass wire for machines with round diamond guides. |
| Gisco MegaCut Brass Hard/Tensile strength 130,000 psi The MegaCut® hard brass EDM wires are subject to the same strict production standards as the other brass and coated wires. CuZn37 (Ms63) is available in a hard temper with a tensile strength of 130,000 PSI and is suitable for auto threading. MegaCut® brass is straightened specifically for use on Japanese machines. It is only available on Japanese standard spools. |
| Gisco MegaCut grip Hart/Tensile strength 130,000 psi Paraffin free wire The MegaCut® grip represents the latest development from Gisco in the segment of brass wire. MegaCut® grip has a paraffin-free surface that guarantees reliable automatic threading and smooth unwinding on the Japanese machines which have automatic threaders. |
| GISCO SOMSAL FAMILY Alloyed with aluminum, these brass wires provide a higher tensile strength. They are suitable for cutting with fine wires in diameters of 0.05 to 0.10 mm under high wire tension. |
| Gisco Somsal 600 Soft/Tensile strength 93.000 psi Due to its high elongation, this version is especially suitable for tapering. Compared to the softer BERCOCUT® series, it provides a higher tensile strength. |
| Gisco Somsal 900 ˝ Hard/Tensile strength 130,000 psi This version, with higher tensile strength than the 600 series, has been tried and tested on machines manufactured by Fanuc and Seibu. |
| Gisco Somsal 1200 Hard/Tensile strength 173,000 psi This electrode with the extremely high tensile strength of 1200 N/mm2 (173,000 PSI), is a preferred choice for precision applications in smaller diameters. |
| GISCO BERCO CUT FAMILY Gisco Berco Cut Super Soft Brass Tensile strength 55,000 psi Softest brass available. It has a high elongation and is suitable for taper cuts greater than 20°. It is recommended as a replacement for the Stamm wire specified by Charmilles for use on 300/310 and 500/510 series. |
| Gisco Berco Cut Brass Tensile strength 71,000 psi Like the coated products, Gisco plain brass EDM wires are subject to strict production standards. For the EDM user, this guarantees reliable and uniform cutting results on EDMs from all manufacturers. CuZn37 (Ms63) is available as plain brass with a tensile strength of 70,000 PSI. |
| Gisco Berco Cut Hard Brass Tensile strength 130,000 psi The hard brass EDM wires are subject to the same strict production standards as the plain brass and coated wires. CuZn37 (Ms63) is available in a hard temper with a tensile strength of 130,000 PSI. Hard Brass wire is suitable for auto threading. |
| GISCO MICROCUT Tensile strength 290,000 psi This EDM wire, especially developed for fine- and micro EDMing is available in diameters down to 0.02mm. With a special zinc-rich brass coating over its high-strength steel core, it provides optimum process stability, the highest dimensional accuracy and superior surface finishes. |
| GISCO MACROCUT This EDM wire has a steel core and a tried-and-tested diffusion annealed, zinc-rich brass coating. Its properties are designed to withstand extreme applications, such as very tall work pieces, interrupted cuts and poor flushing conditions. |